🔧 Adjustable Tile Hole Locator 🛒
🔧 Adjustable Tile Hole Locator 🛒
Couldn't load pickup availability
🔧 Adjustable Tile Hole Locator 🛒
📐 One Wrong Hole Can Ruin the Whole Tile.
You measure.
You mark.
You check again.
Then you drill…
And realize the hole is a little too far left. 😩
Now the pipe doesn’t line up.
The outlet won’t fit.
And that expensive tile may be headed straight for the trash.
The Adjustable Stainless Steel Tile Hole Locator helps you copy the position of existing pipes, sockets and openings before transferring those measurements directly onto the tile.
Measure once.
Lock the position.
Transfer the layout.

Then drill with confidence.
🔧 Stop Guessing Where the Hole Should Go
Tile installation becomes much harder when several openings need to line up perfectly.
Water pipes.
Electrical outlets.
Wall boxes.
Multiple fixtures.
A ruler can tell you the distance.
But this locator helps you physically copy the layout.
That means less:
❌ Re-measuring
❌ Guessing
❌ Drawing multiple reference lines
❌ Misaligned holes
❌ Wasted tile
And more confidence before you make the first cut.
📏 Measure. Lock. Transfer.
The process is simple:
1️⃣ Position the tool
Align the ruler with the wall, pipe, socket or other fixed reference point.
2️⃣ Adjust the arms
Slide and rotate the locator until the built-in hole templates match the positions you need.
3️⃣ Lock the layout
Tighten the adjustment knob so the measurements stay in place.
4️⃣ Move it to the tile
Transfer the exact positioning onto your tile or panel.
5️⃣ Mark the opening
Trace the correct hole template.
Then use your appropriate drill, hole saw or cutting tool separately.
🎯 Copy the Layout Instead of Rebuilding It With Measurements
This is where the tool saves time.
Instead of writing down:
“127mm from the left…”
“92mm from the bottom…”
“Another pipe 68mm over…”
You can physically lock the relative positions into the tool.
Move the whole setup to the tile.
Mark.
Done.
Especially useful when you’re working around multiple plumbing points or wall openings.
🔘 Built-In Hole Templates
The locator includes several common circular opening sizes built directly into the stainless-steel ruler.
Common versions include:
⭕ 25mm
⭕ 40mm
⭕ 45mm
⭕ 55mm semicircle
That makes it easier to mark common pipe and fixture openings without finding a separate template every time.
↔️ Multi-Directional Adjustment
Real walls aren’t always convenient.
Sometimes the opening is above.
Sometimes it’s beside the tile edge.
Sometimes multiple pipes sit at different heights.
The adjustable ruler can slide and rotate to match different layouts before you lock everything into position.
That flexibility is what makes it more useful than a standard fixed ruler.
🧱 Made for Tile Work — Useful Beyond Tile
Use it for layout and hole positioning on compatible materials such as:
🧱 Ceramic tile
🪨 Marble
🪵 Wood panels
🚿 Plumbing installations
🔌 Electrical outlet positioning
💡 Wall fixtures
🏠 Renovation projects
It’s especially useful anywhere the new surface needs to match an opening that already exists behind or beside it.
🔩 Stainless Steel Construction
A positioning tool needs to stay straight.
If the ruler bends or flexes, your measurements become useless.
The stainless-steel construction is designed to provide:
✅ Better rigidity
✅ Repeatable positioning
✅ Resistance to everyday jobsite wear
✅ Clear measurement references
✅ Long-term reusable use
Some current versions use approximately 2.0mm-thick stainless steel for extra rigidity.
📏 Choose the Reach You Need
Depending on the version, the tool is commonly available in:
40cm — Standard Reach
Good for many everyday tile, pipe and outlet positioning tasks.
60cm — Extended Reach
Better when the reference point or multiple openings are farther apart.
Choose based on the size of tile and the distance between the openings you normally work with.
🛠️ Especially Useful Around Plumbing
One of the most frustrating tile jobs?
Several water pipes sticking out of the wall.
You need every opening to line up.
If one is wrong, the tile may not sit flat.
Use the locator to capture the pipe positions first, then transfer them onto the tile before drilling.
Much easier than trying to reconstruct the entire layout using only a tape measure.
🔌 Great for Outlets & Wall Boxes Too
Not every opening is a pipe.
The adjustable layout also helps when positioning around:
Electrical boxes
Sockets
Switch openings
Wall-mounted fixtures
Spotlight positions
Use a reliable reference edge, lock your measurements, transfer the position and verify before cutting.
💸 One Accurate Measurement Can Save an Expensive Tile
Tiles aren’t free.
And once the hole is drilled in the wrong place, there isn’t much room for correction.
A simple positioning tool can help reduce the chance of wasting:
Expensive porcelain tile
Marble
Decorative wall panels
Time
Adhesive
Labor
The tool doesn’t make the hole for you.
It helps make sure you’re putting the hole in the right place first.
🙌 Useful for Pros — Simple Enough for DIY
Professional tilers may use it to speed up repetitive layout work.
DIY renovators can use it to reduce the number of measurements they have to manage at once.
If you can:
Align a ruler
Slide the locator
Tighten a knob
Trace a hole
You can understand the basic workflow.
⚠️ Measure Twice. Verify Once More. Then Drill.
This is a positioning and marking tool.
It does not drill or cut the tile.
Before drilling:
✅ Confirm the locator is aligned to the same reference edge used during measurement
✅ Tighten all adjustment knobs securely
✅ Re-check the transferred position
✅ Confirm the hole diameter
✅ Use the correct drill or cutting tool for your material
A 30-second check is much cheaper than replacing another tile.
❓ Frequently Asked Questions
What does this tool actually do?
It copies and transfers the position of pipes, sockets and other openings so you can mark their location on tile or another compatible surface.
Does it drill the hole?
No.
It measures, positions and marks. You still need a suitable drill, hole saw or cutting tool.
What materials can it be used with?
It is commonly used for ceramic tile, marble, wood panels and other renovation materials where accurate hole positioning is required.
What hole sizes are built in?
Common versions include 25mm, 40mm and 45mm circular openings plus a 55mm semicircular template. Check the exact version you order.
Can it position more than one hole at the same time?
Yes. The adjustable design can help capture and transfer multiple opening positions in one setup.
What sizes are available?
Common versions are available in approximately 40cm and 60cm lengths.
Is it stainless steel?
Yes. Current listings describe the tool as stainless-steel construction.
Can I rotate the ruler?
Yes. The adjustable layout allows multi-directional positioning and rotation before the locking knob is tightened.
📐 Stop Measuring the Same Hole Three Times
The wall already knows where the opening is.
Your tile just needs to match it.
Copy the position.
Lock the layout.
Transfer it directly.
Then make your cut with more confidence.
🔧 Adjustable positioning
📏 Built-in measuring scale
⭕ Multiple hole templates
🔩 Stainless-steel construction
🧱 Tile, marble & renovation use
💸 Helps reduce costly positioning mistakes
👉 Measure. Lock. Transfer. Drill with confidence